Instructions for using the Dyna-Chi Detox Machine

Setting up the Equipment for Treatment

You will need to purchase a foot soaking tub. Make sure your feet fit comfortably in the tub about 6” apart so the Array can sit between them. Place the Power Unit where it will NOT fall into the foot tub of water. If that happens you will be electrocuted, at the very least, you will have a VERY bad day.

Place the Steel Ion Generating Bars (Array) on their side horizontally (so the cables are coming out of the top), in the tub filling it to so that the top of the array is submersed.

IMPORTANT: Add 1 teaspoon of the Himalayan Sea Salt to the water, giving it a few minutes to dissolve. If you feel a tingling around your ankles at the water line, you have too much salt in the water. On the other end of the cables are color coded plugs which go into the power unit’s color coded jacks.

Do not turn on the Power Unit until you have the correct water level, the Himalayan Sea Salt has dissolved, and the wires connected properly.

When removing the Banana Jacks from the power unit, DO NOT PULL ON THE WIRES. Pull on the metal plugs. The cable wires are held in the plugs by compression. It is not unusual for some of the bare wire to be exposed where it enters the plugs.

After placing your feet in the tub water, get comfortable and we suggest doing a 45 minute treatment the first few times you use the system. You should notice bubbles forming on the “Active” Ion Generating Bar of the array.

The optimal water temperature should be that of a very hot bath. However, if you have calluses on the bottom of your feet, we suggest you put extremely hot water in the tub and soak your feet for a few minutes before turning on the system.

During Treatments

Drink at least a quart of water, including electrolytes (such as the “Emer’gen-C” packets) during the treatment! This unit stimulates the Lymphatic System which requires a LOT of water to function properly. If you are dehydrated, do NOT do a treatment.

During the treatment, you may experience a slight feeling of euphoria. This is due to endorphins being released in your brain. Relax and stay stress free during the treatment. Stress is a key factor in the impairment of the Lymphatic System, as is, not being adequately hydrated. Changing the position of your feet in the water is fine. Flexing the muscles in your feet and ankles during the treatment is beneficial.

Try to think of peaceful things or things you love, like kids, pets, partners, etc. during the treatment. Meditation works well. So does prayer. Every few minutes close your eyes, take a few deep, slow breaths focusing on a mental picture of the toxins being pulled down your body and out through the pores of your feet.

How To Interpret the Spa Water after treatment

It is important to keep in mind that much too much emphasis has been placed on “reading” the color of the water by companies selling ineffective systems using Digital Power Units, and Water Modules made from nickel steel.

Those systems systems from China generate around 2 amps of DC power at 10-12 volts. Studies have shown that this is not enough power, even using our advanced water ionizer/Array to do much detoxification. However, the scrap metal used in those system’s water modules WILL turn the water black in about five (5) minutes.

While the color chart is important, and is accurate, people who don’t have Arthritis, Gall Bladder or Liver problems, Candida, Clogged Lymph capillaries, Prostate/Kidney/Urinary Tract problems, or Heavy Metals in their body, will probably only show brown to orange discoloration in the water.

The benefits of our machine including Balancing of the Body’s Energy Field, Eradication of certain Parasites and Infectious Bacteria, Stimulating the Lymphatic and Immune Systems, and the Elimination of Toxins through the GI Tract, will not be indicated by the spa water for obvious reasons.

Following the Treatment

When your treatment is over, turn off the power unit, take your feet out of the water, and wash them well. Unless you feel woozy, a hot shower is good. The stuff in the tub is bodily waste. Flush it down the toilet! Drink plenty of water following the treatment.

It is extremely important to clean the Array immediately following the treatment.

The proper method for cleaning it is to soak it in a container filled with cleaner for 3-5 minutes and then rinse it with hot water. We recommend a product called “The Works”, which is available at all Walmart and Kmart Stores for around $2.50 per quart spray bottle. use a 40 oz. plastic container to soak the array, completely immersing it.

Do not scrub the array, as this often causes damage the the cable's electrical connectors.

If you cannot find The Works, you can use CLR or another lime removing bathroom cleaner.

We also carry a biodegradable cleaner which costs $9.95 per 22 oz. bottle + shipping.

Caveats, Cautions and Common Sense

People with Pacemakers, Transplant Recipients, Electronic Implants, or who are Pregnant should NOT use these units!

Exercise EXTREME caution setting up the power unit so it cannot be knocked into the tub water where your feet are resting. While only 14 volts of DC power comes OUT of the Unit, 120 volt household Alternating Current goes INTO it.

NOTE: You should only use our machine plugged into a GFI (ground fault interrupter) electrical outlet, or a power strip containing a GFI circuit breaker.

Enjoy your new system and the feeling of wellness it beings you!